Penggunaan Minyak Alami dengan Minimum Quantity Lubrication terhadap Hasil Proses Bubut AA 6061
DOI:
https://doi.org/10.21776/ub.jrm.2021.012.01.25Keywords:
AA 6061, Turning Process, MQL, Natural Oil, Surface Roughness.Abstract
Environmentally friendly lubricants are lubricants that are easily dissolved in the environment and are not harmful to the ecosystem. It uses to reduce the heat in the contact area so that the machinability of the workpiece and the ability of the chisel will increase. To minimize the use of bio-cutting fluids, lubrication is carried out by minimum drop lubrication in the lathe process. The purpose of this research is to comply with the surface roughness of the workpiece and the shape of the chip. The material used is aluminum 6061, the natural oil used are rubber seed oil, virgin coconut oil, sunflower seed oil, and castor oil. The turning parameters were the depth of cut 0.5 mm, spindle speed of 330 rpm, feed rate 0.231 mm/rev, tool angle 90o, drop lubrication 192 ml/hour, infeed length 100 mm. The results of the research showed that virgin coconut oil has the lowest surface roughness. This is because the viscosity value of virgin coconut oil is very small so that the flow rate is able to work perfectly to lubricate the contact area. It has a thin chip configuration, the tool also wears but did not experience cracks.
References
SHARMA, A., JOSHI, S.S., DATTA, D., BALASUBRAMANIAM. R., “Investigation Of Tool and Workpiece Interaction On Surface Quality while Diamond Turning Of Copper Beryllium Alloy,â€, Journal Of Manufacturing Science Engineering, N. 142, N. 2, 021011, Feb. 2020.
YILDIRIM, C.V., KIVAK, T., ERZINCANLI, F., “Tool Wear and Surface Roughness Analysis in Milling With Ceramic Tools of Waspaloy: A Comparison Of Machining Performance with Different Cooling Methods,†Journal of The Brazilian Society of Mechanical Sciences and Engineering., v. 41, n. 83, 2019
NOWAK, P., KUCHARSK, K., KAMIŃSKI, M., “Ecological and Health Effects Of Lubricant Oils Emitted Into The Environment,†International Journal of Environmental Research Public Health, v. 16, n.16, 3002, Aug. 2019
WOMA, Y.W., LAWAL. A.S., ABDULRAHMAN, S.A., OLUTOYE, M.A., OJAP, M. M., “Vegetable Oil Based Lubricants: Challenges and Prospectsâ€, Tribology Online, Vol. 14, No. 2, pp 60-70, 2019.
CECILIA, A. J., PLATA, B. D., SABOYA, A. M. R., LUNA, D. T. M. F., CAVALCANTE, C. L., “An Overview Of The Biolubricant Production Process: Challenges And Future Perspectivesâ€, Enrique RodrÃguez-Castellón, v. 8, n.3, 257, 2020.
WERDAA, S., DUCHOSALA, A., QUILLIECA, G. A., MORANDEAUB, A., LEROYA, R., “Minimum Quantity Lubrication: Influence Of The Oil Nature On Surface Integrityâ€, 3rd CIRP Conference On Surface Integrity (CIRP CSI) Procedia CIRP, v. 45, pp. 287 – 290, 2016.
SEN, B., MIA, M., KROLCZYK, G. M., MANDAL, K. U., MONDAL, P. S., “Eco-Friendly Cutting Fluids In Minimum Quantity Lubrication Assisted Machining: A Review On The Perception Of Sustainable Manufacturingâ€, International Journal Of Precision Engineering And Manufacturing-Green Tech-nology, v 8, pp 249–280, 2021.
ARUL, K,, KUMAR, V.S,., “Magnetorheological Based Minimum Quantity Lubrication (Mr-MQL) With Additive N-Cuoâ€, Materials And Manufacturing Processes, v. 35, Issue 4, pp 405-414, 2020
MARTINEZ, G., MIGUEL, V., MARTINEZ, A., MANJABACAS, C. M., COELLO, J., “Sustainable Lubrication Methods For The Machining Of Titanium Alloysâ€, Materials, vol. 12, 3852, 2019.
PAMUJI, R. D., LUSI, N., “Optimasi Parameter Proses Bubut Material ST 60 Dengan Pendinginan Ramah Lingkungan Menggunakan Metode Taguchi-Greyâ€, Jurnal Rekayasa Mesin v. 10, n 3, pp. 245-255, 2019.
WIDIYAWATI, S., NOVAREZA, O., SULISTYARINI, D.H., PUTRO, W. W,“Pengaruh Penggunaan Cairan Pendingin (Coolant) Terhadap Keausan Pahat Bubut Hssâ€, Jurnal Rekayasa Mesin v 11, n 3, pp. 467-475, 2020.
GUNDA, K. R., NARALA, R. K. S., “Electrostatic High-Velocity Solid Lubricant Machining System For Performance Improvement Of Turning Ti–6Al–4V Alloyâ€, Journal of Engineering Manufacture v. 233, n.1, pp 118–131, 2019.
WEIHONG., W., WANG, S., TOMOVIC, M. M., “Mechanical Wear Debris Feature, Detection, And Diagnosisâ€, Chinese Journal Of Aeronautics, v 31, Issue 5, pp 867-882, Mei. 2018.
MABROKI, T., COURBON, C., ZHANG, Y., RECH, J., NAILIAS, D., ASAD, M., HAMDI, H., BELHADI, S., SALVATORE, F., “Some Insights On The Modelling Of Chip Formation And Its Morphology During Metal Cutting Operationsâ€, Comptes Rendus Mécanique, v 344, Issues 4–5, pp 335-354, April-Mei. 2016.
GHOSH, P., PACELLA, M., “Effect Of Laser Texturing On The Performance Of Ultra-Hard Single-Point Cutting Toolsâ€, The International Journal Of Advanced Manufacturing Technology, v 106, pp 2635–2648, 2020.
Downloads
Published
How to Cite
Issue
Section
License
This work is licensed under a Creative Commons Attribution-NonCommercial 4.0 International License.