Pengaruh Variasi Persentase Reduksi pada Proses Pengerolan Panas terhadap Sifat Mekanik dan Struktur Mikro Baja Laterit

Authors

  • Permana Andi Paristiawan Indonesian Sciences Institute
  • Vinda Puspasari Indonesian Sciences Institute
  • Andika Widya Pramono Indonesian Sciences Institute
  • Bintang Adjiantoro Indonesian Sciences Institute

DOI:

https://doi.org/10.21776/ub.jrm.2020.011.02.16

Keywords:

Hot Rolling Process, Laterite Steel, Mechanical Properties, Microstructure

Abstract

Lateritic ore is one of the raw materials for the steel industry. Lateritic ore processed into laterite steel has more advantages than steel in the market. It has better tensile strength, hardness, corrosion resistance, and welding properties. Lateritic steel is made by performing a casting process. This research aims to investigate the effect of reduction percentage on mechanical properties and microstructure of the lateritic steel after the hot rolling process. The specimens were heated to austenitization temperature at 10000C for 1 hour before the rolling process. The reduction percentage varies by 10%, 15%, and 20%. Hardness and impact test was conducted using a Rockwell Hardness and Charpy method. The microstructure was observed using an optical microscope. The results showed the optimum hardness of 58 HRC in a hot rolling sample with 20% reduction. The highest impact strength of 46 Joule and ductile fracture took place in this sample. The microstructure of this sample showed a bainitic phase causing lower hardness.

References

PRASETYO, P., “Sumber daya mineral di Indonesia khususnya bijih nikel laterit dan masalah pengolahannya sehubungan dengan UU Minerba 2009â€, Dalam: Seminar Nasional Sains dan Teknologi, pp. 1-10, Jakarta, Nov. 2016.

SUBAGJA, R., PRASETYO, B., SARI, W.M., “Peningkatan kadar nikel dalam laterit jenis limonit degan cara peletasi, pemanggangan reduksi dan pemisahan magnet campuran bijih, batu bara, dan Na2SO4â€, Jurnal Material Metalurgi., v. 31, n. 2, pp. 103–115, Aug. 2016.

SIAHAAN, E., dan RIZA, A., “The effect of hot rolling on hardness properties and microstructure of laterite steelâ€, In: Proceeding of Tarumanagara International Conference on the Applications of Technology and Engineering: IOP Conference Series: Materials Science and Engineering, v. 508, Jakarta, May. 2019.

HERBIROWO, S., HAKIM, L., ADJIANTORO, B., “Microstructure and mechanical characteristics of hot forged lateritic steelsâ€, In: International Mechanical and Industrial Engineering Conference 2018: MATEC Web of Conferences, v. 24, pp. 1–6, Malang, Sep. 2018.

WANG, Y., CHEN, Y., WEI, H., ZHAO, Y., LIU, Z., “Effect of hot rolling process parameters on microstructure transformation and microstructure of 45MnSiV steelâ€, Materials Science Forum, v. 944, pp. 265–271, Jan. 2019.

PRAMUDIA, M., dan ROMADHON, A. S., “Pengaruh variasi ukuran bola baja pada proses dry shoot peening terhadap mikrostruktur dan kekerasan material implan AISI 316Lâ€, Jurnal Rekayasa Mesin, v. 9, n. 3, pp. 169–172, Dec. 2018.

DENG, G. Y. et al., “Evolution of microstructure, temperature and stress in a high speed steel work roll during hot rolling : Experiment and modellingâ€, Journal of Materials Processing Technology, v. 240, pp. 200–208, Oct. 2017.

DONG, Q., CAO, J., WEN, D., “Spalling prevention and wear improvement of rolls in steel strip hot-rolling processâ€, Journal of Failure Analysis and Prevention, v. 15, pp. 626-632, Oct. 2015.

CALLISTER, W. D., and RETHWISCH, D. G., Fundamental of materials science and engineering: an integrated approach, 4 Ed., New York, John Wiley & Sons, Inc, 2012

WIDODO, T. D., dan RAHARJO, R., “Pengaruh ball peening terhadap kekerasan baja tahan karat AISI 316Lâ€, Jurnal Rekayasa Mesin, v. 7, n. 3, pp. 151–155, 2016.

LIU, Z. et al., “Microstructure evolution and mechanical property of low-alloy steel used for armor layer of flexible pipe during thermomechanical process and hot rolling processâ€, Journal of Materials Engineering and Performance, v. 28, pp. 107-116, Nov. 2019.

BUDIYANTO, E., CHOIRON, A., dan DARMADI, D. B., “Hardening baja AISI 1045 menggunakan gel aloe vera sebagai media pendinginâ€, Jurnal Rekayasa Mesin, v. 7, n. 2, pp. 55–64, 2016.

SUJITNO, T., MULYANI, E., ANDRIYATI, W., SUHARLAN, D., and MALAU, V., “Effect of diamond-like carbon thin film on the fatigue strength of AISI 4340â€, Advances in Materials, v. 8, n. 1, pp. 21–26, March. 2019.

HAN, J. et al., “The effects of prior austenite grain boundaries and microstructural morphology on the impact toughness of intercritically annealed medium Mn steelâ€, Acta Materialia, v. 122, pp. 199–206, Jan. 2017.

JAFARLOU, H., HASSANNEZHAD, K., ASGHARZADEH, H., & MARAMI, G. R., “Enhancement of mechanical properties of low carbon steel joints via graphene additionâ€, Materials Science and Technology, v. 34, n. 4, pp. 455–467, Dec. 2017.

HASSANPOUR, H., SADEGHI, H., RASTI, A., and SHAJARI, S., “Investigation of Surface Roughness, Microhardness and White Layer Thickness in Hard Milling of AISI 4340 Using Minimum Quantity Lubricationâ€, Journal of Cleaner Production, v. 120, pp. 124-134, 2016.

CAI, Z. H., DING, H., XUE, X., amd XIN, Q. B., “Microstructural evolution and mechanical properties of hot-rolled 11 % manganese TRIP steelâ€, Materials Science & Engineering A, v. 560, pp. 388–395, 2013.

LIU, Z. et al., “Microstructure Evolution and Mechanical Property of Low-Alloy Steel Used for Armor Layer of Flexible Pipe During Thermomechanical Process and Hot Rolling Processâ€, Journal of Materials Engineering and Performances, v. 28, pp. 107-116, 2019.

PLATOV, S. I., NEKIT, V. A., and MASLENNIKOV, K. B., “Strength , ductility and impact toughness of tube steels after hot rollingâ€, In: IOP Conference Series: Materias Science and Engineering, v. 709, n. 3, Jan. 2020.

FRAS, T., ROTH, C. C., MOHR, D., “Fracture of high-strength armor steel under impact loadingâ€, International Journal of Impact Engineering, v. 111, pp. 147-164, Jan. 2018.

RIDLO, F.M., PARISTIAWAN, P.A., UTAMA, D.P., CITRAWATI, F., “Study on the effect of solution treatment soaking time on structure development of modified FeNiMn steelsâ€, AIP Conference Proceedings, v. 2232, n.1, 2020.

ALSHWIGI, M., PUTATUNDA, S.K., and BOILEAU, J., “Metallurgy and Metal Physics Development of Dual Phase Microstructure in Medium Carbon Low Alloy Steel by Continuous Cooling Heat Treatment,†International Journal of Metallurgy and Metal Physics, v. 3, n. 2, pp. 1-13, Oct. 2018.

PRASETYO, M.A., PUSPASARI, V., ANWAR, M.S., NIKITASARI, A., MABRURI, E., “Mechanical properties of modified cast martensitic stainless steel CA6NM with addition of molybdenum and nitrogenâ€, AIP Conference Proceedings, v. 2232, n.1, 2020.

KIM, B. et al., “Effects of Ni and Cu addition on cryogenic-temperature tensile and charpy impact properties in austenitic 22Mn-0.45Ce1Al steelsâ€, Journal of Alloys and Compounds, v. 815, n. 152407, Jan, 2020.

TAKASHIMA, Y., “Fracture toughness evaluation for dissimilar steel joints by Charpy impact test,†Welding in the World, v. 63, pp. 1243–1254, June. 2019.

Downloads

Published

2020-08-15

Issue

Vol. 11 No. 2 (2020)

Section

Articles

License