Rancang Bangun CNC Plasma Cutting

Authors

  • Saiful Irfan Universitas Negeri Semarang
  • Rusiyanto Rusiyanto Universitas Negeri Semarang

DOI:

https://doi.org/10.21776/ub.jrm.2021.012.01.1

Keywords:

CNC Plasma Cutting, Safety Factor, Precision

Abstract

This study aims to determine the frame safety factor and the precision level of CNC plasma cutting results. The research method used is a research and development model, namely the French model. This model has 8 steps that are used to produce a CNC plasma cut design. The data analysis technique used is descriptive statistical analysis techniques derived from the results of tests conducted. Safety factor testing was conducted using the 2015 Autodesk Inventor software with a frame of 110.54 N. The precision cutting results were carried out three times using the same instrument, 20 currents with a speed of 400 mm/min, against ST 37 material with a thickness of 1.3 mm. The results showed that the frame was categorized as safe because the minimum safety factor value was 4.23 ul and the cut test results showed an average measurement with a maximum deviation of 0.3 mm, so it could be concluded that plasma CNC cutting had tolerance. rate of ± 0.3 mm.

Author Biography

Saiful Irfan, Universitas Negeri Semarang

 

References

DINATA GERRY, G. S., A. Z. MUTTAQIN., dan M. DARSIN., “Rancang Bangun Dan Uji Performasistem Kendali Pemberian Fluida Pemesinan MQL Berbasis Arduinoâ€, Rekayasa Mesin , v. 11, n. 1, pp. 97-104, Mar. 2020.

KISTANTO, A. R., B. LIPITO dan F. DAISE., “Desain Sistem Mekanik Plasma Cutter Menggunakan Prinsip Run Stabilizer Processâ€, Jurnal Teknologi Pertanian Gorontalo, v. 3, n.1, pp. 29-43, Apr. 2018.

PAWAR, S. S. dan K. H. INAMDAR., “Experimental Analysis of Plasma Arc Cutting Process for SS 316l Platesâ€, In: Nasional Conference RDME, e-ISSN: 2278-1684,p-ISSN: 2320-334X, India, March. 2017.

TRIVEDI, K. H., J. P. MEHTA dan D. P. KUNDALIYA., “Design and Development Of Three Axis Plasma Cutting Machineâ€, IJARIIE, v. 3, n. 3., pp. 694-703, Juli. 2017.

MARTANA, B., Y. DJAYA dan M. A. LUKMANA., “Development of Plate Cutting CNC with Laser Cutter and Stepper Motor Driverâ€, Dalam: Prosiding SNTTM XVI, pp 62-66 Jakarta Selatan, Okt. 2017.

AMRI, A. A. N. dan W. SUMBODO., “Perancangan 3D Printer Tipe Core XY Berbasis Fused Deposi-tion Modeling (FDM) Menggunakan Software Autodesk Inventor 2015â€, Jurnal Dinamika Vokasional Teknik Mesin,v. 3, n. 2, pp. 110-115, Okt. 2018

PRIANTO, E dan H. S. PRAMONO., “Proses Permesinan Dalam Pembelajaran Simulasi CNCâ€, Jurnal Edukasi Elektro, v. 1, n. 1, pp. 62-68, Mei. 2017.

NURSYAHUDDIN, D. dan D. GASNI., “Proses Perancangan Mekanik Dengan Pendekatan Terintegrasi: Studi Kasus Perancangan Alat Uji Pin On Discâ€, TEKNIKA, v. 21, n. 1, pp. 14-29, Mar. 2014.

SHINDE, M. E. dan S. S. LAKADE., “Design and Development of A Torch Head Mechanism for A CNC Plasma Cutting Machineâ€, IJSTE , v. 2, n. 4, pp. 136-141, Okt. 2015.

SETYONO, B., MRIHRENANINGTYAS dan A. HAMID., “Perancangan Dan Analisis Kekuatan Frame Sepeda Hibrid “Trisona†Menggunakan Software Autodesk Inventorâ€, Jurnal IPTEK, v. 20, n. 2, pp. 305-308, Des. 2016.

SUGIYONO., Metode Penelitian Pendidikan, Edisi 11., Bandung, Alfabeta, 2015.

IMRAN, A. I. dan KADIR., “Simulasi Tegangan Von Mises Dan Analisa Safety Factor Gantry Crane Kapasitas 3 Tonâ€, DINAMIKA Jurnal Teknik Mesin,v. 8, n. 2, pp. 1-4, Mei. 2017.

SURDIA, T dan S. SAITO., Pengetahuan Bahan Teknik, Cetakan Ke-4., Jakarta, PT. Pradnya Paramita, 1999.

CAHYONO, E. dan B. M. ARIANTO., Rancang Bangun Meja Mesin Plasma Cutting Dengan Gerak 3 Axis X, Y, Z, Menggunakan Motor Stepper Berbasis Arduino, Program Studi Diploma III., Institut Sepuluh Nopember, Surabaya, 2017.

SULARSO dan K. SUGA., Dasar Perencanaan Pemilihan Elemen Mesin, Edisi 11., Jakarta, PT. Pradnya Paramita, 2004.

Downloads

Published

2021-05-31

Issue

Section

Articles