Analisa Perkembangan Struktur Aluminum (AC2B) dengan Pengaruh Penambahan Stronsium pada Part Transmisi Sub Assy Menggunakan Metode Pengecoran Gravity Dies Casting

Dikky Antonius, Budiarto Budiarto, Priyono Atmadi, Rakha Anugrah Pratama

Abstract


Recently, one of the problems faced by the automotive industry is the frequent failure parts produced by casting processes such as uncomplete filling, low mechanical properties, shrinkage (non-uniform shrinkage), and porosity. In this research, the modification method with the addition of strontium while aluminum being melted is held. This experiment was made to solve either the shrinkage problem or porosity. The improvement of the mechanical properties of aluminum also become one of the purposes of the experiment. The concentration of strontium added was 0 wt.% Sr, 0.005wt.% Sr, 0.0075wt.% Sr, and 0.01 wt.%. The results show that the increased Sr content on AC2B will increase the mechanical properties, while the optimum value occurred by addition value 0.01wt. % Sr. However the results also show that the concentration of strontium has no effect on reducing shrinkage porosity, and can reduce the size of aluminum dendrites.

Keywords


Modifier; AlSr; AC2B; Gravity Die Casting; Transmisi Sub Assy

Full Text:

PDF

References


B. S. WARDHANA, “Pengaruh Penambahan Fraksi Berat Zirconia terhadap Sifat Fisik dan Mekanik Komposit Aluminium Diperkuat Zirconia yang diproduksi dengan Metalurgi Serbuk,” Jurnal Rekayasa Mesin, vol. 5, pp. 263 - 269, 2014.

W. M. RASMUSSEN, Aluminium Casting Technology, Pensyvalnia State: American Foundrymen's Society, 1993, 1986.

J.R.DAVIS, ASM SPECIALTY HANDBOOK: Aluminium and Aluminium Alloys, Ohio, 1993.

R. GALLO, Gas Porosity In Aluminium Casting. Compiled Literature., American Foundry Society, 2002.

J. BROWN, FOSECO NON-FERROUS FOUNDRYMAN’S HANDBOOK, Auckland: Foseco Interna-tional Ltd, 1999.

A. S. H. A. P. G. SANDERS, “Hypoeutectoid Aluminium-Silicon Alloy Development for Graw-Based 3D Printing using Wedge Casting,” International Journal of Metalurgy, vol. 11, pp. 843 - 856, 2017.

A. I. TEAM, ASM SPECIALTY HANDBOOK 15: Casting, Ohio: ASM international, 2008.

D. E. M. S. N. GAUTAM KRISHNAN.R, “Study of Strontium in Aluminium Alloy,” International Jour-nal of Engineering Technology and Advanced Engineering, vol. 3, pp. 753-760, 2013.

SUHERMAN, A. PANJAITAN, S. MIZHAR dan A. HANDOKO, “Pengaruh Penambahan Sr terhadap Struktur Mikro Kekerasan dan Ketangguhan Paduan Aluminium A319,” Politeknik Tanjung Balai, 2017.

J. E. GRUZELSKI dan B. CLOSSET, Treatment of Liquid Aluminium-Silicon Alloys, American Found-rymen's Society, 1990.

C. M. MR. MANJUNATH dan D. PUROHIT, “A Study of Microstructure and Mechanical Properties of Aluminium Silicon Carbide Metal Matrix Composites (MMC’s),” International Journal of Engineering Research and Technology (IJERT), vol. 2, pp. 690 - 700, 2013.

B. KULUNK dan D. ZULIANI, “Applications for the Strontium Treatment of Wrought and Die-Cast AI,” JOM, pp. 60 - 61, 1996.

D. STUART, D. MCDONALD, “Eutectic grain size and strontium concentration in hypoeutectic alumin-ium–silicon alloys,” Journal of Alloys and Compounds, vol. 442, pp. 184 - 191, 2006.

J.M. YU, “Influence of impurities, strontium addition and cooling rate on microstructure evolution in Al-10Si-0.3Fe casting alloys,” Journal of Alloys and Compound, vol. 766, pp. 818 - 827, 2018.

N. TENEKEDJIEV dan J. E. GRUZLESKI, “Hypereutectic Aluminium-Silicon Casting Alloys—A Re-view,” CAST METALS, vol. 3, pp. 96 - 105, 1990.

W. D. CALLISTER, Material Science and Engineering an Introduction, Canada: John Willey & Sons, Inc, 1997.

I. AMERICAN FOUNDRYMEN`S SOCIETY, second Edition: Aluminium Casting Technology, 1997.




DOI: https://doi.org/10.21776/ub.jrm.2019.010.03.4

Refbacks

  • There are currently no refbacks.


Creative Commons License
This work is licensed under a Creative Commons Attribution-NonCommercial 4.0 International License.