PERILAKU OKSIDASI ISOTERMAL PADUAN 68,5Fe-14Ni-9Al-7,5Cr-1Mo PADA TEMPERATUR 800, 900, DAN 1000°C
DOI:
https://doi.org/10.21776/jrm.v15i3.1814Keywords:
Isothermal Oxidation, Ferritic Steel, High Temperature Oxidation, High Temperature MaterialsAbstract
Extensive research has been conducted on high-temperature alloys for power generation, with chromium-forming ferritic iron as the primary basis for these materials. However, the practical applications of these materials are limited to temperatures below 800°C. This study addresses the development of an alumina-forming 68.5Fe-14Ni-9Al-7.5Cr-1Mo austenitic iron-based alloy, isothermally oxidized at 800, 900, and 1000°C for 1, 10, 50, and 150 h, respectively. The formation of the protective layer was characterized using X-ray diffraction (XRD) and energy dispersive spectroscopy (EDS) attached in a scanning electron microscope (SEM). The thickness of the oxide layer was quantified using the ImageJ software. XRD analysis of the sample that had been oxidized for 150 h at various temperatures revealed the presence of Al2O3. The clustered grain morphology was observed at the sample's surface oxidized for 150 h at 800°C. In contrast, the sample oxidized at 900°C exhibited a hair morphology, and the sample oxidized at 1000°C exhibited a wrinkled morphology. EDS mapping of all samples revealed that O and Al dominated the oxide scales. Measurements of oxide thickness indicated an accelerated growth phase during the first 10 hours of exposure, which was subsequently followed by a gradual slowing down in growth rates over more extended periods of time
References
PT. Perusahaan Listrik Negara, “Rencana Usaha Penyediaan Tenaga Listrik 2015-2024,” Jakarta, 2015.
D. Zhang, “Introduction to advanced and ultra-supercritical fossil fuel power plants,” in Ultra-Supercritical Coal Power Plants: Materials, Technologies and Optimisation, 2013, pp. 1–20.
P. Liaw, “Computational Design of Creep-Resistant Alloys and Experimental Validation in Ferritic Superalloys,” United States, 2014. doi: 10.2172/1182543.
C. Stallybrass and G. Sauthoff, “Ferritic Fe-Al-Ni-Cr alloys with coherent precipitates for high-temperature applications,” Mater. Sci. Eng. A, vol. 387–389, no. 1-2 SPEC. ISS., pp. 985–990, 2004, doi: 10.1016/j.msea.2004.01.108.
Y. Yanas, “Pengendapan Nano-Presipitat B2-(Fe,Ni)Al pada Baja Feritik Maju,” Institut Teknologi Bandung, 2016.
A. Shirzadi and S. B. T.-S. A. for P. P. Jackson, Eds., “Structural Alloys for Power Plants: Operational Challenges and High-temperature Materials,” in Woodhead Publishing Series in Energy, Woodhead Publishing, 2014, pp. xv–xx.
Eddy Agus Basuki, Panduan Logam untuk Aplikasi Temperatur Tinggi dan Penghematan Energi. Bandung: Penerbit ITB, 2019.
G. C. Wood, “High-temperature oxidation of alloys,” Oxid. Met., vol. 2, no. 1, pp. 11–57, 1970, doi: 10.1007/BF00603581.
P. Eklund, M. Sridharan, G. Singh, and J. Bøttiger, “Thermal Stability and Phase Transformations of γ-/Amorphous-Al2O3 Thin Films,” Plasma Process. Polym., vol. 6, no. S1, pp. S907–S911, Jun. 2009, doi: https://doi.org/10.1002/ppap.200932301.
M. Sridharan, M. Sillassen, J. Bøttiger, J. Chevallier, and H. Birkedal, “Pulsed DC magnetron sputtered Al2O3 films and their hardness,” Surf. Coatings Technol., vol. 202, no. 4, pp. 920–924, 2007, doi: https://doi.org/10.1016/j.surfcoat.2007.05.061.
A. Mavrič, M. Fanetti, G. Mali, and M. Valant, “High-temperature stabilization of bulk amorphous Al2O3,” J. Non. Cryst. Solids, vol. 499, pp. 363–370, 2018, doi: https://doi.org/10.1016/j.jnoncrysol.2018.07.055.
D. J. Young, High Temperature Oxidation and Corrosion of Metals: Second Edition. Elsevier Inc, 2016.
I. Rommerskirchen, B. Eltester, and H. J. Grabke, “Oxidation of β-FeAl and Fe-Al alloys,” Mater. Corros., vol. 47, no. 11, pp. 646–649, Nov. 1996, doi: https://doi.org/10.1002/maco.19960471109.
V. K. Tolpygo, “The Morphology of Thermally Grown α-Al2O3 Scales on Fe-Cr-Al Alloys,” Oxid. Met., vol. 51, no. 5, pp. 449–477, 1999, doi: 10.1023/A:1018839227090.
W. H. Gitzen, Alumina as a ceramic material. United States: American Ceramic Society, 1970.
S. Bachri, “Studi Evolusi Struktur Mikro Paduan Baja Feritik Fe-14Ni-9Al-7,5Cr-1Mo pada temperatur 800, 900, dan 1000℃,” Institut Teknologi Bandung, 2018.
E. Airiskallio et al., “High temperature oxidation of Fe–Al and Fe–Cr–Al alloys: The role of Cr as a chemically active element,” Corros. Sci., vol. 52, no. 10, pp. 3394–3404, 2010, doi: https://doi.org/10.1016/j.corsci.2010.06.019.
L. P. H. Jeurgens, W. G. Sloof, F. D. Tichelaar, and E. J. Mittemeijer, “Growth kinetics and mechanisms of aluminum-oxide films formed by thermal oxidation of aluminum,” J. Appl. Phys., vol. 92, no. 3, pp. 1649–1656, Aug. 2002, doi: 10.1063/1.1491591.
X. Teng, L. Sheng, X. L. Zhang, and Z. G. Zhang, “The Effect of the Third Element Cr on Oxidation Behavior of Fe-xCr-10Al (at.%) Alloys at 900°C,” Open Corros. J., vol. 2, no. 1, pp. 37–44, 2009, doi: 10.2174/1876503300902010037.
R. Prescott, D. F. Mitchell, G. I. Sproule, and M. J. Graham, “Transport in α-Al2O3 scales on FeAl and NiAl alloys at 1100°C,” Solid State Ionics, vol. 53–56, pp. 229–237, 1992, doi: https://doi.org/10.1016/0167-2738(92)90386-4.
E. A. GULBRANSEN and W. S. WYSONG, “Thin oxide films on aluminum,” J. Phys. Colloid Chem., vol. 51, no. 5, pp. 1087–1103, Sep. 1947, doi: 10.1021/j150455a004.
D. C. Nababan, “Perilaku Oksidasi Isotermal Paduan 69,5Fe-14Ni-9Al-7,5Cr pada Temperatur 800, 900 dan 1000℃,” Institut Teknologi Bandung, 2017.
B. A. Pint, J. R. Martin, and L. W. Hobbs, “The oxidation mechanism of θ-Al2O3 scales,” Solid State Ionics, vol. 78, no. 1, pp. 99–107, 1995, doi: https://doi.org/10.1016/0167-2738(95)00013-V.
Downloads
Published
How to Cite
Issue
Section
License
Copyright (c) 2025 Fadhli Muhammad, Eddy Agus Basuki
This work is licensed under a Creative Commons Attribution-NonCommercial 4.0 International License.
This work is licensed under a Creative Commons Attribution-NonCommercial 4.0 International License.
