FABRIKASI DAN PENGUJIAN TELAPAK KAKI PALSU JENIS SINGLE AXIS
DOI:
https://doi.org/10.21776/jrm.v15i3.1622Keywords:
Disabilities, Prosthetic foot, Shore hardness, Compression test, Fatigue testAbstract
Along with the increasing number of persons with disabilities, the need for prosthetic foot has also increased. However, the irony is that some of the products circulating in Indonesia are still imported from abroad, while the domestic product is quite limited and possesses some drawbacks. This study aims to study the production process of the single axis type of the right-side prosthetic foot as well as to evaluate the performance of this product. The prosthetic foot in this research was made from thermoplastic polyurethane (TPU) resin and prepared with casting by pouring it into a pre-fabricated mold. A single-axis type of right prosthetic product could have been successfully made in this study with men's shoe sizes EU 42 and a mass of 654 g. The result of evaluation of the material and foot prosthetic product showed an average Shore hardness value of 54.3 HA. According to the result of compression test, this prosthetic product was also able withstand the highest compressive load up to 259.76 kgf. Finally, the result of fatigue test showed no damage on the foot prosthetic product until 90.000 cycle.
References
Center for Disease Control and Prevention, “Disability and Health Overview,” 2020. https://www.cdc.gov/ncbddd/disabilityandhealth/disability.html (accessed Feb. 02, 2023).
Pemerintah Indonesia, “Undang-Undang Republik Indonesia Nomor 8 Tahun 2016 tentang Penyandang Disabilitas.” Sekretariat Negara. Jakarta, Jakarta, 2016.
M. Asif et al., “Advancements, Trends and Future Prospects of Lower Limb Prosthesis,” IEEE Access, vol. 9, pp. 85956–85977, 2021, doi: 10.1109/ACCESS.2021.3086807.
M. R. Pitkin, Biomechanics of Lower Limb Prosthetics. Berlin: Springer, 2010.
P. S. Selvam, M. Sandhiya, K. Chandrasekaran, D. H. Rubella, and S. Karthikeyan, “Prosthetics for Lower Limb Amputation,” Prosthetics Orthot., vol. 11, p. 13, 2016, doi: http://dx.doi.org/10.5772/intechopen.95593.
J. Gibbons, The Vital Glutes: Connecting The Gait Cycle to Pain and Dysfunction. California: North Atlantic Books, 2014.
P. K. Kumar, M. Charan, and S. Kanagaraj, “Trends and Challenges in Lower Limb Prosthesis,” IEEE Potentials, vol. 36, no. 1, pp. 19–23, 2017, doi: 10.1109/MPOT.2016.2614756.
J. I. Krajbich, M. S. Pinzur, B. K. Potter, and P. M. Stevens, Atlas of Amputations and Limb Prosthetics. Surgical, Prosthetic and Rehabilitation Principles., 4th ed., vol. 1. Rosemont: American Academy of Orthopaedic Surgeons, 2018.
D. A. P. Anggaraksa, “Rancang Bangun Telapak Kaki Palsu Jenis Solid Ankle Cushion Heel (SACH),” Universitas Islam Indonesia, 2022.
L. O. G. A. Prayuda, “Desain Dan Simulasi Telapak Kaki Palsu Dengan Variasi Cavity,” Universitas Islam Indonesia, 2020.
I. J. Ferreira, “Design and Manufacture of a Customized Prosthetic Foot,” Instituto Superior Tecnico, Lisboa, Portugal, 2019.
A. A. Wicaksono, “Rancang Bangun Alat Uji Fatigue Telapak Kaki Palsu Berdasarkan Standar ISO 10328,” Universitas Islam Indonesia, 2021.
R. Budi, “Perancangan Sistem Otomasi Alat Uji Fatigue Telapak Kaki Buatan Berbasis Arduino,” Universitas Islam Indonesia, 2021.
A. Leonardo, A. D. Soewono, and M. Darmawan, “Rancang Bangun Dan Karakterisasi Feeding Mechanism Silikone Berbasis Syringe Pump Pada 3D Printer,” J. Rekayasa Mesin, vol. 13, no. 1, pp. 109–118, 2022, doi: 10.21776/ub.jrm.2022.013.01.12.
R. Hari Krishnan, V. Devanandh, A. K. Brahma, and S. Pugazhenthi, “Estimation of mass moment of inertia of human body, when bending forward, for the design of a self-transfer robotic facility,” J. Eng. Sci. Technol., vol. 11, no. 2, pp. 166–176, 2016.
Downloads
Published
How to Cite
Issue
Section
License
Copyright (c) 2025 Christianus Pigun Wardoyo, Muslim Mahardika, Suyitno Suyitno, Rini Dharmastiti, Urip Agus Salim, Budi Arifvianto

This work is licensed under a Creative Commons Attribution-NonCommercial 4.0 International License.

This work is licensed under a Creative Commons Attribution-NonCommercial 4.0 International License.