DESIGN OF NATURAL FIBER POWDER MACHINE
DOI:
https://doi.org/10.21776/jrm.v15i1.1482Keywords:
Natural Fiber, Pineapple Leaf Fiber, Prescriptive Design, MachineAbstract
Natural fiber processing is the type of fiber as raw materials for textile or other industries that can be obtained directly from nature. In the Indonesian automotive industry, the manufacture of parts in vehicles is Polypropylene high impact (PPHI). An example of an existing part is a CVT slide piece made with a mixed polymer composite material from PPHI and pineapple leaf fiber. Pineapple leaf fibers with small sizes are needed so that the mixing of polymer composites is good. Therefore modern technology is required to process pineapple leaf fibers. This final project makes a natural fiber powder machine for processing natural fiber, namely scavenging. The research methodology used is a prescriptive design method. The design results produce a natural fiber powder machine (pineapple leaf fiber) for polymer composite materials with long size specifications of 420 mm long, 300 mm wide, and 582 mm high. The production capacity of the natural fiber storage machine is 5 kg/h. The source of the engine drive is a 1 HP AC electric motor with a rev of 2800 rpm. The transmission system uses a V-belt with a drive shaft 30 mm in diameter. The frame construction is made of a 35x35x5 mm profile with ST42 material and knives using S45C material (AISI 1045) with a thickness of 10 mm. It uses nine dynamic blades and six sharp plane fixed blades in a 30-degree active blade and a 60-degree fixed blade.
References
A. E. Latief, L. Darusman, W. P. Fahla, A. D. Zaidan, and N. D. Anggraeni, “Perancangan Cetakan Injection Molding Hand Press Untuk Produk Slide Piece CVT Menggunakan FEM,” Jurnal Sistem Mekanik dan Termal , vol. 5, no. 2, pp. 105–113, 2021.
A. E. Latief, N. D. Anggraeni, and D. Hernady, “Karakterisasi Mekanik Komposit Matriks Polipropilena High Impact Dengan Serat Alam Acak Dengan Metode Hand Lay Up Untuk Komponen Automotive,” Jurnal Rekayasa Hijau, vol. 3, no. 3, 2019.
M. Y. Firdaus and A. E. Latief, “Pengujian Karakterisasi Material Komposit Berpenguat Serat Alam Fraksi Volume 10% Menggunakan Metode Injection Molding,” Jurnal Seminar Nasional-XIX, pp. 13–22, 2020.
N. D. Anggraeni, A. E. Latief, M. R. J. Alfano, and T. D. Aprilianto, “Analisis Bending pada Komposit PPHI (Polypropylene High Impact) Berpenguat Serat Nanas dengan Fraksi Volume 20% yang Dibuat Menggunakan Injection Molding,” Jurnal Seminar-XIX, pp. 8–12, Dec. 2020.
R. Biantoro and C. A. Purwita, “Review: Pembuatan Serat Rayon,” JURNAL SELULOSA, vol. 9, no. 02, p. 51, Dec. 2019, doi: 10.25269/jsel.v9i02.273.
K. R. Sumesh, K. Kanthavel, and V. Kavimani, “Machinability of hybrid natural fiber reinforced composites with cellulose micro filler incorporation,” J Compos Mater, pp. 1–17, Oct. 2020, doi: 10.1177/0021998320918020.
N. S. Mardiyati and R. S. Steven, “Sifat tarik dan sifat impak komposit polypropylene high impact berpengaruh serat rami acak yang dibuat dengan metode injection molding.”,” 2017.
F. R. Ernawan, M. A. M. Kramadibrata, and A. Widyasanti, “Uji Kinerja Dan Analisis Energi Mesin Penepung Vertikal (Mill Dryer Vertical) Tipe MDV-10 (Studi Kasus Techno Park Pangan Grobogan, Kabupaten Grobogan, Jawa Tengah),” Jurnal Ilmiah Mahasiswa Agroinfo Galuh, vol. 6, no. 1, pp. 243–258, 2019.
H. Sukma and M. R. Kamarullah, “Perancangan Mesin Penggiling Sekam Padi,” Jurnal Vokasi Indonesia, vol. 9, no. 2, pp. 23–38, Dec. 2021.
D. Ariwibowo, “Karakteristik Alat Penepung Disc Mill FFC-XX Untuk Penepungan Tongkol Jagung Kering,” Jurnal Teknik Mesin Rotasi, vol. 18, no. 3, pp. 69–75, Jul. 2016, [Online]. Available: http://ejournal.undip.ac.id/index.php/rotasi
E. Reinaldy, “Rancang Bangun Mesin Penepung Rumput Laut ATC Kapasitas 10 Kg/Jam,” Tugas Akhir, Universitas Sultan Ageng Tirtayasa, Cilegon, 2019.
N. D. Anggraeni and A. E. Latief, “Rancang Bangun Mesin Pencacah Plastik Tipe Gunting,” Jurnal Rekayasa Hijau, vol. 2, no. 2, pp. 185–190, 2018.
H. Ardianto and M. Tamjidillah, “Rancang Bangun Mesin Penyerbuk Kayu Kapasitas 130 Kg/Jam Dan Penepung Sekam Dalam Satu Poros Untuk Kebutuhan Pembuatan Media Baglog Jamur Tiram,” Jurnal Tugas Akhir Mahasiswa Rotary, vol. 4, no. 1, pp. 90–100, 2022, [Online]. Available: https://ppjp.ulm.ac.id/journals/index.php/rot
G. Fenske and L. Ajayi, “Identification Of Critical Process Parameters For Knife Milling And Alternative Comminution Strategies,” Jurnal Argonne National Laboratory, pp. 6–25, 2020.
E. Saefudin, Marsono, and E. P. Nugraha, “Modifikasi Pisau Mesin Penepung ATC Dengan Garis Mata Potong Pada Sudut 330 Arah Radial,” Jurnal Teknik Mesin, vol. 6, no. 2, pp. 36–42, 2020.
A. Widyanugraha, A. Santosa, and D. T. Santoso, “Perancangan Mesin Penggiling Padi dan Penepung Sekam Padi Skala Rumah Tangga,” JURNAL Teknik Mesin, vol. 13, no. 2, pp. 69–75, 2020, [Online]. Available: http://ejournal2.pnp.ac.id/index.php/jtm
W. K. Sugandi, A. Yusuf, T. Herwanto, and A. M. Ummah, “Uji Kinerja Dan Analisis Ekonomi Mesin Penepung Biji Jagung (Studi Kasus Di Desa Cikawung, Kecamatan Ciparay, Kabupaten Bandung),” Jurnal Teknik Pertanian Lampung, vol. 8, no. 2, pp. 107–119, Jun. 2019.
M. Arfiyanto, “Perancangan Mesin Pencacah Rumput Pakan Ternak,” Universitas Negeri Yogyakarta, Yogyakarta, 2012.
Sularso and K. Suga, Dasar Perencanaan Dan Pemilihan Elemen Mesin, 10th ed. Jakarta: PT. Pradnya Paramita, 2002.
W. Widodo and R. Hakim, “Pengembangan Alat Bantu Arbor untuk Pembuatan Roda Gigi pada Mesin Frais Vertikal,” Jurnal Rekayasa Mesin, vol. 12, no. 2, pp. 287–296, Aug. 2021, doi: 10.21776/ub.jrm.2021.012.02.6.
Downloads
Published
Issue
Section
License
Copyright (c) 2024 Ali Attamimi, Alfan Ekajati Latief, Zidane Nassem, Riski Gunarto Ramadan
This work is licensed under a Creative Commons Attribution-NonCommercial 4.0 International License.
This work is licensed under a Creative Commons Attribution-NonCommercial 4.0 International License.
