RANCANG BANGUN PROTOTIPE PREPARASI MATERIAL RESISTANCE SPOT WELDING
DOI:
https://doi.org/10.21776/jrm.v14i2.1466Keywords:
Iron Plate, Bluetooth Module, Resistance Spot Welding, Quality of Welded Joints, Surface RoughnessAbstract
The manufacturing process in the automotive industry is in dire need of resistance spot welding machines. Because it was easier to use, highly effective, and effective in functioning. However, there were sometimes still connection problems that were still of poor quality, both nuggets and areas that are subject to electrode pressure. To get a quality welding connection, a machine was needed that was able to carry out good material preparation in the form of sanding, able to set the welding current analogously, able to set the time with an automatic timer, able to apply pressure on the electrode measurably during the welding process. The research aimed to design a prototype of resistance spot welding material preparation that could adequately carry out material preparation and welding using a Bluetooth system connected to a mobile phone. The research methods carried out were as follows: first, designing the machine using Autodesk Inventor software, then the device was made with a focus on material preparation prototypes, then the machine elements were made for the material clamping rail, then the machine elements in the control section using Bluetooth connected to the mobile phone, the machine was tested, then the connection quality testing process was carried out on the tensile testing machine. The results showed that the design results had been made using elbows and iron plates with threaded rails with a length of 650 mm, which became material clamping rail grooves with a drive using window motors controlled by Bluetooth on the Arduino circuit. The test results of welded joints show that the roughness is 0.20 μm which has the highest tensile strength.
References
P. Bamberg, R. Seewald, A. Schiebahn, U. Reisgen, N. Precoma, and M. Epperlein, “Improvement of the resistance spot welding of Al-Mg-Si alloys by using cladding technology: An optical and mechanical characterization study,” J. Adv. Join. Process., vol. 5, no. December 2021, p. 100090, 2022, doi: 10.1016/j.jajp.2021.100090.
M. de Leon and H. S. Shin, “Prediction of Optimum Welding Parameters for Weld-Quality Characterization in Dissimilar Ultrasonic-Welded Al-to-Cu Tabs for Li-ion Batteries,” Met. Mater. Int., vol. 29, no. 4, pp. 1079–1094, 2022, doi: 10.1007/s12540-022-01271-z.
A. Chabok, H. Cao, E. van der Aa, and Y. Pei, “New insights into the fracture behavior of advanced high strength steel resistance spot welds,” J. Mater. Process. Technol., vol. 301, no. August 2021, p. 117433, 2022, doi: 10.1016/j.jmatprotec.2021.117433.
T. B. Watmon, C. Wandera, and J. Apora, “Characteristics of resistance spot welding using annular recess electrodes,” J. Adv. Join. Process., vol. 2, no. October, p. 100035, 2020, doi: 10.1016/j.jajp.2020.100035.
Ariyanto, H. Arsyad, M. Syahid, and R. Ilyas, “Optimization of Welding Parameters for Resistance Spot Welding with Variations in the Roughness of the Surface of the AISI 304 Stainless Steel Joint to Increase Joint Quality,” Int. J. Mech. Eng. Robot. Res., vol. 11, no. 11, pp. 877–883, 2022, doi: 10.18178/ijmerr.11.11.877-883.
G. N. Nigon, O. B. Isgor, and S. Pasebani, “The effect of annealing on the selective laser melting of 2205 duplex stainless steel : Microstructure , grain orientation , and manufacturing challenges,” Opt. Laser Technol., vol. 134, no. September 2020, p. 106643, 2021, doi: 10.1016/j.optlastec.2020.106643.
H. Dong, W. Hu, Y. Duan, X. Wang, and C. Dong, “Dissimilar metal joining of aluminum alloy to galvanized steel with Al-Si, Al-Cu, Al-Si-Cu and Zn-Al filler wires,” J. Mater. Process. Technol., vol. 212, no. 2, pp. 458–464, 2012, doi: 10.1016/j.jmatprotec.2011.10.009.
D. M. Rezaei, B. Heidarshenas, and F. Baniasadi, “Determination of nugget size in resistance projection welding by means of numerical method and comparison with experimental measurement,” no. October, pp. 1–34, 2018, doi: 10.20944/preprints201810.0249.v1.
A. Chabok, E. Van Der Aa, and Y. Pei, “Materials Science & Engineering A A study on the effect of chemical composition on the microstructural characteristics and mechanical performance of DP1000 resistance spot welds,” Mater. Sci. Eng. A, vol. 788, no. April, p. 139501, 2020, doi: 10.1016/j.msea.2020.139501.
I. Riady, “Rancang Bangun Mesin Spot Welding dengan Menggunakan Pengatur Arus Dimmer,” Univ. Muhamadiyah Surabaya, vol. 1, no. 1, 2021.
Subarjo and T. Widodo, “Subarjo: Modifikasi Mesin Las Titik Portable,” TekTanJurnal Ilm. Tek. Pertan., vol. 12, no. April, pp. 1–64, 2020.
S. Roth, A. Hezler, O. Pampus, S. Coutandin, and J. Fleischer, “Influence of the process parameter of resistance spot welding and the geometry of weldable load introducing elements for FRP/metal joints on the heat input,” J. Adv. Join. Process., vol. 2, no. June, p. 100032, 2020, doi: 10.1016/j.jajp.2020.100032.
I. K. Al Naimi, M. H. Al Saadi, K. M. Daws, and N. Bay, “Influence of surface pretreatment in resistance spot welding of aluminum AA1050,” Prod. Manuf. Res., vol. 3, no. 1, pp. 185–200, 2015, doi: 10.1080/21693277.2015.1030795.
X. Sun, Q. Zhang, S. Wang, X. Han, and Yongbing, “Effect of adhesive sealant on resistance spot welding of 301L stainless steel.” 2020, doi: 10.1016/j.jmapro.2020.01.033.
K. R. Kashyzadeh et al., “Resistance Spot Welding of Aluminum 6063 Alloy for Aerospace Application: Improvement of Microstructural and Mechanical Properties,” J. Inst. Eng. Ser. D, vol. 5, no. December 2021, pp. 366–377, 2022, doi: 10.1007/s40033-021-00324-8.
Y. Lu, A. Peer, T. Abke, M. Kimchi, and W. Zhang, “Subcritical heat affected zone softening in hot-stamped boron steel during resistance spot welding,” Mater. Des., vol. 155, no. 2017, pp. 170–184, 2018, doi: 10.1016/j.matdes.2018.05.067.
H. Long, Y. Hu, X. Jin, J. Shao, and H. Zhu, “Effect of holding time on microstructure and mechanical properties of resistance spot welds between low carbon steel and advanced high strength steel,” Comput. Mater. Sci., vol. 117, pp. 556–563, 2016, doi: 10.1016/j.commatsci.2016.01.011.
T. Dai and J. C. Lippold, “The effect of postweld heat treatment on hydrogen-assisted cracking of 8630/Alloy 625 overlay,” Weld. World, vol. 62, no. 3, pp. 581–599, 2018, doi: 10.1007/s40194-018-0578-6.
H. Haikal, “Pengaruh Parameter Pengelasan Resistance Spot Welding terhadap Sifat Fisik dan Mekanik Multi-Layer Logam Tak Sejenis Berbeda Ketebalan,” Mach. J. Tek. Mesin, vol. 7, no. 1, pp. 16–24, 2021, doi: 10.33019/jm.v7i1.1661.
M. L. Sonjaya, M. Mutmainnah, and M. F. Hidayat, “Construction of Plastic Waste Extruding Machine to Produce Filaments of 3D Printing Machine,” Int. J. Mech., vol. 16, pp. 82–90, Jul. 2022, doi: 10.46300/9104.2022.16.10.
N. Ali Sutisna, M. Irfan Satria, J. Ki Hajar Dewantara, and C. Bekasi, “Development of Robotic Arm Controller Using Arduino Microcontroller and Mobile Device Application,” Rotasi, vol. 24, no. 2, pp. 75–86, 2022.
Downloads
Published
How to Cite
Issue
Section
License
Copyright (c) 2023 Ariyanto Ariyanto, Iman Pradana A. Assagaf, Rifaldy Ramadhan Latief, Fajar Reski Maulana, Gusrifar Gusrifar, Muh. Aqdar Fitrah, Muhammad Ikhsan
This work is licensed under a Creative Commons Attribution-NonCommercial 4.0 International License.
This work is licensed under a Creative Commons Attribution-NonCommercial 4.0 International License.
