PEMBUATAN DAN PENGUJIAN SIFAT MEKANIK WELDING SPESIMEN LOGAM DISSIMILAR AISI 1015 DENGAN AISI 304L MENGGUNAKAN PROSES GMAW
DOI:
https://doi.org/10.21776/jrm.v15i1.1461Keywords:
AISI 1015, ASS 304L, Hypo Eutectoid, HAZ, MAGAbstract
The manufacture of specimens produced by MAG welding on the joining of metal plates not AISI 1015 with SS304L, must meet the welding standards used. Low carbon steel AISI 1015 and stainless steel SS304L were used in this experiment by applied different current variations to each sample, namely 120, 130 and 140A in MAG welding using ER70S6 electrode. The results of the examination on the identification of the macro appearance in the heat affected area (HAZ) and Vickers microhardness and tensile testing were carried out in this study. From the data obtained, the hardness value of the weld metal is higher when compared to the parent metal between AISI 1015 and SS304L, and the hardness value of the weld metal is also higher due to the influence of the ER70S6 solid wire electrode used. The tensile strength and yield strength of MAG welded joints increased at 120 and 140A, and the fault position occurred in hypo euctectoid steel (AISI 1015) at the boundary between the heat affected area and the parent metal. The results of the research on MAG welded joints with a welding current of 120A is preferably used for joining dissimilar metals between low carbon steel (AISI 1015) and austenitic stainless steel (AISI 304L).
References
Pierpaolo Carlone, Antonello Astarita., “Dissimilar metal welding”, Metals, v. 9, n, 11, pp. 1206, 2019.
Yang, J, Wang, L., “Optimizing the local strength mismatch of a dissimilar metal welded joint in a nuclear power plant”, Metals, v. 8, pp. 494, 2018.
Jai Paul Dudeja., “Analysis and advantages of welding dissimilar metal by fiber laser”. International Journal of advanced Scientific Technologies in Engineering and Management Sciences, v. 5, August. 2018.
L.O.Osaba, I.C. Ekpe, R.A.Elemuren., “Analysis of dissimilar welding of austenitic stainless steel to low carbon steel by tig welding process”, International Journal of Metallurgical & Materials Science and Engineering (IJMMSE), v. 5, pp. 1-12, Oct. 2015.
T.E.Abioye.,O.E. Ariwoola.,T.I. Ogedengbe.,P.K. Farayibi., O.O.Gbadeyan., “Effect of welding speed on the microstructure and corrosion behavior of dissimilar gas metal arc weld joints of aisi 304 stainless steel and low carbon steel”, International Conference on Recent Advanced in Materials, Minerals & Enviroment (RAMM), Proceedings, pp. 871 – 877, 2019.
Bambang Teguh Baroto., Petrus Heru Sudargo., “Pengaruh arus listrik dan filler pengelasan logam berbeda baja karbon rendah (st 37) dengan baja tahan karat (aisi 316l) terhadap sifat mekanis dan struktur mikro”, Prosiding SNATIF ke -4, , ISBN 978, 2017.
Winarto., Winarto., Muhammad Anis, Teguh Puji Hertanto., “Mechanical Properties and Microstructure of Welded Dissimilar Metals using Buttering & Non-Buttering Layer, Advanced Materials Research, v. 789, pp. 341-346, 2013.
M.F.Mamat.,E.Hamzah.,Z.,Ibrahim.,Rohah.A.M.,A.Bahador., “Effect of filler metals on the microstructures and mechanical properties of dissimilar low carbon steel and 316l stainless steel welded joints”, Materials Science Forum, v. 819, pp 57 -62, 2015.
M.Velu, Sunil Bhat, “Metallurgical and Mechanical examinations of steel – copper joints arc welding using bronze and nickel base superalloy filler materials”, Materials and Design, v. 47, pp. 793-809, 2013.
Tarng Y., Yang W., “Optimisation of the weld bead geometry in gas tungsten arc welding by the Taguchi method”, Int J Adv Manuf Technol, v. 14(8), pp. 549-545, 1998.
Juang S, Tarng Y.,”Process parameter selection for optimizing the weld pool geometry in the tungsten inert gas welding of stainless steel”, J Mater Process Technol, v. 122, pp. 33-37, 2002.
Bodkhe Sc., Dolas DR.,”Optimization of activated tungsten inert gas welding of 304L austenitic stainless steel”, Procedia Manufacturing, v. 20, pp. 277-282, 2018.
Handa A., Chawla V, “An investigation on the effect of axial pressures on the mechanical properties of friction welded dissimilar steels”, Advances in Mechanical Engineering, v. 2014, pp. 1-6, 2014.
Emad Kh. Hamd.,Abbas Sh. Alwan.,Ihsan Khalaf Irthiea, “Study the Effect of Welding Heat Input on the Microstructure, Hardness, and Impact Toughness of AISI 1015 Steel”, Al-Khwarizmi Engineering Journal, Vol. 14, No.1, pp. 118-127, 2017.
Rechard S.Sabo,"The procedure Handbook of Arc welding ", The lincolin electric company, Cleveland, Ohio44117, Australia, 1999.
P.Cico., D.Kalincova., M.Kotus., “Influence of welding method on microstructural creation of welded joints”, Res.Agr.Eng., v. 57, (Special Issue): S50 – S56, 2011.
Khubaib Zafar Ghumman., Sadaqat Ali., Emad Ud Din., Aamir Mubashar., Niaz Bahadur Khan., Syed Waqar Ahmed.,”Experimental investigation of effect of welding parameters on surface roughness, micro-hardness and tensile strength of AISI 316L stainless steel welded joints using 308L filler material by TIG welding”, Journal of Materials Research and Technology, v. 21, pp. 220-236, 2022.
Santillan Esquivel A., Nayak S S., Xia M S., Zhou Y., “Microstructure, hardness and tensile properties of fusion zone in laser welding of advanced high strength steels”, Mechanical Performance of Welds, v. 51, pp. 328-335, 2012.
Downloads
Published
How to Cite
Issue
Section
License
Copyright (c) 2024 Riswanda Riswanda, Harlian Kadir, Albert Saragih

This work is licensed under a Creative Commons Attribution-NonCommercial 4.0 International License.

This work is licensed under a Creative Commons Attribution-NonCommercial 4.0 International License.