PENGARUH PENGUJIAN KEKERASAN DAN PENGUJIAN TEKAN TERHADAP KARAKTERISTIK GAYA TUMBUKAN PADA CANGKANG KENARI (CANARIUM INDICUM L)
DOI:
https://doi.org/10.21776/jrm.v15i1.1227Keywords:
Bending, Compressive Force, Impact, Mechanical Properties, Walnut ShellAbstract
Kenari (Canarium indicum L) belongs to the Burseraceae family and is one of the endemic fruits in Indonesia, especially Maluku. Walnuts have a tough shell that encloses the flesh, to get the flesh without damaging it careful effort is needed. This study investigated the strength of walnut shells through mechanical testing to determine the amount of impact force needed to break the walnut shell. The mechanical test carried out is a compression test and impact test. The values of these tests assist in determining, measuring, and analyzing the minimum and maximum force loads required to crack a walnut shell. Tests were carried out on walnut shells from 6 different villages on Ambon Island and Saparua Island. The impact test where the highest impact absorption energy value was found in walnut shells from Booi Village, namely 23.18 J/mm2, and the lowest in walnut shells from Morela Village, 22.40 J/mm2. In the compression test where the lowest value was found in walnut shells from Morela village with a value of 3.61 MPa while the highest value was found in walnut shells from Booi village, namely 5.24 MPa. Whereas the minimum compressive force is 16.22 kgf/mm2 and the maximum compressive force is 17.61 kgf/mm2.
References
Ismail, A.I., Rasidah, R., dan Haliq, R., “Pengaruh masaa filler matriks terhadap sifat mekanik dan daya serap air pada komposit cangkang biji karet”, Jurnal Rekayasa Mesin, v. 12, n. 2, pp. 297 – 304, 2021.
Bonisoli, E., Delprete, C., Sesana, R., Tamburro, A., Tornincasa. S., “Testing and simulation of threepoint bending anistropic behaviour of hazelnut shells”, Biosystems Engineering, v. 129, n. pp. 134-141, 2015.
Braga, G.C., Couto, S.M., Hara, T., Neto, J.T.P.A., “Mechanical behaviour of macadamia nut under compression loading”, Journal of Agricultural Engineering Research, v. 72, n. 3 pp. 239-245, 1999.
Carcel, L.M., Bon, J., Acuna, L., Nevares, I., Alamo, M., Crespo, R,. “Moisture dependence on mechanical properties of pine nuts from pinus pinea L.”, Journal of Food Engineering, v. 110, n. 2, pp. 294- 297, 2012.
Delprete, C., Sesana, R., “Mechanical characterization of kernel and shell of hazelnut: Proposal of an experimental procedure”, Journal of Food Engineering, v. 124, pp. 28-34, 2014.
Kashaninejad, M., Mortazavi, A., Safekordi, A., Tabil, L.G., “Some physical properties of pistachio (Pistacia vera L.) nut and its kernel”, Journal of Food Engineering, v. 72, n. 1, pp. 30-38, 2006.
Koyuncu, M.A, Ekinci, K., Savran, E., “Cracking characteristic of walnut”, Journal of Biosystem Engineering, v. 87, n. 3, pp. 305-311, 2004.
Thomson, L.A.J., and Evans, B., “Canarium indicum var. Indicum and C. Harveyi (Canarium Nut)”, Spesies Profiles For Pacific Island Agroforestry, 2006.
Mohsenin, N.N., Physical properties of plant and animal materials. Structure, physical characteristics and mechanical properties, 2nd ed, Gordon and Breach Science Publishers, 1986.
Nanulaitta, N.M., Soeprapto, W., Soenoko, R., “Pengaruh Fraksi Volume Serat Empulur Sagu (Metroxylon sp) dan Presentase Alkali terhadap Pengujian Impak serta Absorpsi Air pada Komposit Berserat Sagu”, Jurnal Rekayasa Mesin, v. 9, n. 3, pp. 163-168, 2018.
Odewole, M.M., and Ajibade, R.O., “Fabrication and Perfomance Evaluation of Thevetia Nut Cracking Machine”, Nigerian Journal Of Technological Development, v. 12, n. 1, pp. 12-17, 2015.
Ozguven, F., Vursavus, K., “Some physical, mechanical and aerodynamic properties of pine (pinus pinea) nuts”, Journal of Food Engineering, v. 68, n. 1, pp.191-196, 2005.
Hanang, P.A., Tamrin, dan Oktafri, “Uji Kinerja Alat Pemecah Benih Kelapa Sawit”, Jurnal Teknik Pertanian Lampung, v. 6, n. 2, pp. 115-124, 2017.
Ruzuqi, R., Waas, V.D., “Analisis kekuatan tarik dan impak material komposit polimer dalam aplikasi fiberboat”, In: Prosiding Seminar Nasional Archipelago Engineering, 2021.
Siallagan, A.Y., Daulay, S.B. dan Harahap, L.D., Pemecahan Cangkang Kemiri (Aleurites moluccana) Menggunakan Sistem Ripple Mill Dengan Berbagai Suhu Perendaman, Skripsi Sarjana, Univ. Sumatera Utara, 2012.
Sitkei G., Mechanics of agricultural materials. Developments in Agricultural Engineering 8, Elsevier Science Publishers, 1986.
Sinaga, R., Analisis Gaya Tumbukan Pemecah Biji Kemiri (Aleurites moluccana Wild.), Tesis, Institut Pertanian Bogor, 2017.
Downloads
Published
How to Cite
Issue
Section
License
Copyright (c) 2024 Leslie S. Loppies, Alexander A. Patty, Berthy Pelasula, Roy R. Lekatompessy, Nevada Mario Nanulaitta
This work is licensed under a Creative Commons Attribution-NonCommercial 4.0 International License.
This work is licensed under a Creative Commons Attribution-NonCommercial 4.0 International License.
