PERANCANGAN MODIFIKASI MESIN BENDING ROTARY BAJA APLIKASI STAND POT BUNGA
DOI:
https://doi.org/10.21776/jrm.v13i2.1077Keywords:
Bending, Bending Rotary, Stand PotAbstract
Plants grown in pots continue to grow year after year. A flower pot support or flower pot stand is required to add aesthetic value and save space. The purpose of this research is to develop a steel rotary bending machine design for flower pot stand applications The method used is to calculate the rotational speed of the bending mall, design the transmission, calculate the power and capacity of the machine, calculate and analyze the frame strength, and produce machine design results. The design produces a mall bending rotation of 4.5 rpm with diameters of 100 mm, 120 mm, and 150 mm, an electric motor with a rotation speed of 2840 rpm and a power of 1 HP, 4 pulleys and 2 types A V-belts, a shaft diameter of 20 mm and a 6 x 6 mm key, UCP and UCF type bearings, conical gears with a reduction of 10:16, a gearbox with a reduction of 1:40. The required power is 146 watt (0,2 horsepower), and the engine capacity is 243 bends per hour. The engine frame has dimensions of 750 x 550 x 1000 mm and is made of AISI 1045 material. The highest stress that occurs in the frame is 45.55 N/mm2.
References
BADAN PUSAT STATISTIK, “Statistik tamanan hias indonesia”, Publisher : Badan Pusat Statistik, Jakarta 2018.
NURCAHYO, YUSUF EKO dkk, Rancang bangun mesin roll bending portable. Teknika: Engineering and Sains Journal, v. 2, n. 2, pp 109-114, Desember 2018.
LOVELY, S., FENDRA, S., Rancang bangun alat bending sengkang pada kolom skala laboratorium. Jurnal Teknika ISSN: 0854-8471, v. 21 n.3, pp 76-83, Desember 2014
VILAS, S., DARSHAN, dkk., Design and fabrication of hydraulic stirrups making machine, International Journal of Innovative Research in Science, Engineering and Technology, v.5, n.3, pp 8362-8366, May 2016
ROSSBANDRIO, WOWO dkk. 2015. Analisa tekanan bending besi bar pada alat planetary bending. Jurnal Integrasi. v. 7, n. 1, pp. 36-39, Februari 2018
SUMIATI, RUZITA dkk, “Pembuatan dan pengujian mesin bending rotary baja untuk aplikasi stand pot bunga diameter 8 dan 10 inci” Jurnal Teknik Mesin, v.13, n. 1, pp 13-17. Juni 2020
RICHARD, G., BUDYNAS, N., KEITH. J., SHIGLEY’s, Mechanical Engineering Design, Nineth Edition. New York: Mc. Graw Hill, 2011.
KEMDIKBUD RI , “Mekanika Teknik dan Elemen Mesin 2”, Jakarta, Kemdikbud, 2015
SULARSO., KIYOKATSU SUGA, “Dasar Perencanaan Dan Pemilihan Elemen Mesin”, Jakarta: Pradnya Paramita, 2014
KHURMI, R. S., J. K. GUPTA. “Machine design”, Edisi 11, New Dehli, Eurasia Publishing House Limited, 2004.
PAUL M. KUROWSKI, ”Engineering analysis with solidworks simulation 2012”, Schroff Development Corporation 2012
CALLISTER, WILLIAM D.,” Materials science and engineering an introduction”, John Wiley & Sons, Inc.New York. 2009
FAUZI, RAHMAN. “Rancang bangun mesin penggulung tali rafia” , Jurnal Teknik Mesin V. 12, n. 1, pp 10-18, Juni 2020.
RUHYAT dkk. “Perancangan mesin pemutar cairan primer GL-711” Jurnal Sinergi, V. 13, n. 3, pp 19-2, Oktober 2009
WUNDA, SEVERIANUS dkk. 2019. “Analisis tegangan, regangan dan deformasi crane hook dari material baja AISI 1045 dan baja ST 37 menggunakan software elmer”, Jurnal Fisika, V. 4 n. 2, pp 131-138, April 2019
MOSTAFA ABDALLA,”Aircraft stress analysis and structural design”, Version 1.02, Delft University of Technology The Netherlands. Januari 2008
Downloads
Published
Issue
Section
License
Copyright (c) 2022 Ruzita Sumiati
This work is licensed under a Creative Commons Attribution-NonCommercial 4.0 International License.
This work is licensed under a Creative Commons Attribution-NonCommercial 4.0 International License.
