PENGARUH SUDUT KEMIRINGAN TERHADAP PUTARAN DAN DAYA HIDROLISIS PADA TURBIN ARCHIMEDES SCREW PORTABLE
DOI:
https://doi.org/10.21776/ub.jrm.2022.013.01.25Keywords:
Archimedes Screw, Picohydro, hydrolysis power.Abstract
Picohydro Power Plant is one of the renewable energy sources which utilizes water or irrigation channels with a small head and flow rate. Many factors can affect the hydrolysis power and also the power on the rotation of the screw turbine, one of which is the turbine design. The existing turbine design needs to be evaluated by several factors such as inner and outer screw diameters, slope, screw pitch, number of blades and condition of inlet and outlet as well as head and water flow. Moreover, if the turbine is designed for a portable one with a length of approximately only 1 meter. These factors indicate that the design of each screw turbine design needs to be optimized through data analysis to find the optimal hydraulic power and turbine rotation. This study aims to determine the effect of the tilt angle of the Archimedes screw turbine on the turbine rotation and also the hydraulic power of the picohydro power plant with variations of the turbine tilt angle (K) 20°, 30° and 40°. The method used in this research is to use a Performance Experiment Study by making an Archimedes screw turbine as a picohydro power plant. From the test results using a discharge of 2 ltr/sec, the largest turbine rotation is 144.3 at a 30° turbine tilt angle with 10.77 Watt of produced hydraulic power (P).
References
H. Budi Harja, H. Abdurrahim, S. Yoewono, and H. Riyanto, “Penentuan Dimensi Sudu Turbin dan Sudut Kemiringan Poros Turbin pada Turbin Ular Archimedes,†Met. Indones., vol. 36, no. 1, p. 26, 2016, doi: 10.32423/jmi.2014.v36.26-33.
M. W. N. Karim, M. Widyanrtono, A. C. Hermawan, and S. I. Haryudo, “KAJIAN KEMIRINGAN BLADE DAN HEAD TURBIN ARCHIMEDES SCREW TERHADAP DAYA KELUARAN GENERATOR AC 1 PHASE 3 kW Muhammad Wildan Nur Karim Mahendra Widyartono , Aditya Chandra Hermawan , Subuh Isnur Haryudo Abstrak,†Tek. Elektro, vol. 10, pp. 219–228, 2021.
M. A. Wahid and Z. Erwanto, “Perencanaan dan penerapan prototipe pembangkit listrik tenaga piko hidro (pltph) dengan turbin tipe undershoot,†vol. 6, no. 1, pp. 81–87, 2020.
W. D. Lubitz, “Archimedes Screw Turbines : A Sustainable Development Solution for Green and Renewable Energy Generation — A Review of Potential and Design Procedures,†2020.
F. A. S. Putra, “Pengaruh Variasi Kemiringan Propeller,†Universitas negeri semarang, 2019.
I. P. Juliana, A. I. Weking, and L. Jasa, “Pengaruh Pengaruh Sudut Kemiringan Head Turbin Ulir Terhadap Daya Putar Turbin Ulir Dan Daya Output Pada Pembangkit Listrik Tenaga Mikro Hidro,†Maj. Ilm. Teknol. Elektro, vol. 17, no. 3, p. 393, 2018, doi: 10.24843/mite.2018.v17i03.p14.
A. T. Saputra, A. I. Weking, and I. W. Artawijaya, “Eksperimental Pengaruh Variasi Sudut Ulir Pada Turbin Ulir (Archimedean Screw) Pusat Pembangkit Listrik Tenaga Mikro Hidro Dengan Head Rendah,†vol. 18, no. 1, pp. 83–90, 2019.
G. Dellinger, A. Terfous, P. A. Garambois, and A. Ghenaim, “Experimental investigation and performance analysis of Archimedes screw generator,†J. Hydraul. Res., vol. 54, no. 2, pp. 197–209, 2016, doi: 10.1080/00221686.2015.1136706.
L. J. Ardika Kadek Agus, Antonius Ibi Weking, “Analisa Pengaruh Jarak Sudu Terhadap Putaran Turbin Ulir Pada Pembangkit Listrik Tenaga Mikro Hidro,†Majalah Ilmiah Teknologi Elektro, pp. 217–226, 2019.
Downloads
Published
Issue
Section
License
Copyright (c) 2022 Gunawan Rudi Cahyono, Apip Amrullah, Pathur Razi Ansyah, Rusdi -

This work is licensed under a Creative Commons Attribution-NonCommercial 4.0 International License.

This work is licensed under a Creative Commons Attribution-NonCommercial 4.0 International License.