ANALISIS TEGANGAN PISAU PENCACAH LIMBAH KAKAO DENGAN METODE BEDA HINGGA
DOI:
https://doi.org/10.21776/jrm.v13i2.1052Keywords:
Crusher Machine, Crusher Blade, Cocoa Waste, Finite Element Simulation, 3 DimensionsAbstract
One of the vital components of a crushing machine is a crushing blade. Where the crusher blade works and is in direct contact with the cocoa waste to be crushed. Many crushing blades wear out quickly after being used for a short time because the blade material has low strength.The aim of this study was to analyze the blade in the crusher machine used by farmers to handling cocoa waste. The blade usings material of steel by utilizing waste car spring sheets with ASTM A29 steel type which is formed into a crusher blade because the price is cheap and easy to obtain. 3-D finite element design and analysis were carried out using Solidwork software. The blade is given a load variation from 100N - 1000N to determine the value of stress, deformation, and safety factor. The results of the simulation and analysis on the crusher blade show a downward trend starting at a load of 400 N, where the stress is 444,738 N/mm2, the maximum shape change is 3.48066 mm, and the safety factor seems to be low in the red distribution with FOS below 1, which is 0.989347.
References
T. P. SUB DIREKTORAT STATISTIK, Statistik Kakao Indonesia 2017. Badan Pusat Statistik, 2018.
M. IQBAL and D. AZMI, “Kebijakan Pengembangan Agribisnis Kakao Melalui Primatani : Kasus Kabupaten Luwu , Provinsi Sulawesi Selatan,” J. Anal. Kebijak. Pertan., vol. 4, no. 1, pp. 39–53, 2006.
P. HENING and U. BUDI, “Pemanfaatan Limbah Kulit Buah Kakao ( Theobroma Cocoa L .) sebagai Adsorben Zat Warna Rhodamin B,” in Prosiding Seminar Nasional Fisika dan Pendidikan Fisika (SNFPF), 2014, vol. 5, pp. 12–18.
Y. NYIMAS, “Optimasi aktivator dalam pembuatan kompos organik dari limbah kakao,” Majalah Ilmiah Mektek, vol. 15, no. 2, 2013.
H. SURIPTO, SUKARMAN, APRIZA, Y. RIZA, and S. ANWAR, “Pembuatan Mesin Pencacah Single Blade Kapasitas 100 kg/jam dengan Metode Pahl & Beitz,” J. APTEK, vol. 13, no. 2, pp. 83–89, 2021.
M. ANDRIANTO and F. FAHRIANSYAH, “Mesin Pencacah Limbah Kulit Kakao,” J. Engine Energi, Manufaktur, dan Mater., vol. 3, no. 1, p. 1, 2019, doi: 10.30588/jeemm.v3i1.480.
N. H. BAHARI, BUDIANTO, and F. HAMZAH, “Rancang Bangun Mesin Pengolah Sampah Organik Menjadi Bahan Pupuk Kompos dan Pencacah Pakan Ternak Berdaya Listrik Berkapasitas 25 kg / jam,” in Proceedings Conference on Design Manufacture Engineering and its Application, 2017, pp. 161–167.
I. M. A. KUNCORO and B. TRIYONO, “Perancangan Mesin Pencacah Plastik Portabel Dengan Memanfaatkan Limbah Pegas Daun Kendaraan Sebagai Material Pisau Potong,” in Prosiding The 11th Industrial Research Workshop and National Seminar, 2020, pp. 26–27.
F. OLAWALE S, A. STEPHEN A, and A. ESTHER T, “The Effects of Sn Addition on the Microstructure and Surface Properties of Laser Deposited Al-Si- Sn Coatings on ASTM A29 Steel,” in ICMMPE 2017, 2018, pp. 1–11.
C. P. YEPES, P. ROMERO, and M. ANGEL, “Analysis by Means of the Finite Element Method of the Blades of a PET Shredder Machine with Variation of Material and Geometry,” J. Contemp. Eng. Sci., vol. 11, no. 83, pp. 4113–4120, 2018, doi: 10.12988/ces.2018.88370.
A. SUTRISNA, SYAWALDI, DEDIKARNI, and J. RAHARJO, “Design of Dry Leaves Shredder Machine Using Five Blades,” J. Renew. Energy Mech., vol. 2, no. 2, pp. 66–80, 2019, doi: 10.25299/rem.2019.vol2(02).3532.
W. K. SUGANDI, A. YUSUF, and A. THORIQ, “Rancang Bangun Mesin Pengupas Talas Semir,” Rekayasa Mesin, vol. 8, no. 2, pp. 67 – 74, 2017, doi: 10.23960/jtep-l.v9i1.19-27.
F. RESTU, R. HAKIM, and F. S. ANWAR, “Analisa Kekuatan Material ASTM A36 pada Konstruksi Ragum terhadap Variasi Gaya Cekam dengan Menggunakan Software SolidWorks 2013,” J. Integr., vol. 9, no. 2, p. 113, 2017, doi: 10.30871/ji.v9i2.444.
A. FELANI, “Analisis Statis Konstruksi dan Lance Tube Sootblower Tipe Motorised Rotary Menggunakan Software Solidworks 2016,” Rekayasa Mesin, vol. 12, no. 2, pp. 243–250, 2021.
M. SYAIFUL FADLY, A. PURNOWIDODO, and P. HADI SETYARINI, “Karakteristik Fiber Metal Laminate Akibat Beban Impak Balistik Dari Peluru Kaliber 9 mm Full Metal Jacket (FMJ),” Rekayasa Mesin, vol. 12, no. 1, pp. 103–116, 2021.
Z. FUADI EMZAIN, H. SHYH-CHOUR, Y. YU-SHENG, and N. QOSIM, “Design and Analysis of a Dynamic Splint Based on Pulley Rotation for Post-Stroke Finger Extension Rehabilitation Device,” Rekayasa Mesin, vol. 11, no. 3, pp. 477–485, 2020.
I. R. RAHMAT, “Analisis Beban pada Hook Pembalik Produk AEET dengan Software Solidwork 2018,” PRIMA, vol. 17, no. 1, pp. 10–18, 2020.
Z. ABIDIN and P. J. ARYADI, “Analisis Struktur Sepeda Lipat IZI ARC 16 dengan menggunakan Metode Elemen Hingga,” J. Rekayasa Mesin, vol. 21, no. 1, pp. 1–5, 2021.
L. A. N. WIBAWA, “Studi Numerik Pengaruh Radius Fillet dan Ketebalan Cap terhadap Tegangan Von Mises dan Faktor Keamanan Silinder Berdinding Tipis untuk Tabung Motor Roket,” J. Rekayasa Mesin, vol. 15, no. 1, p. 1, 2020, doi: 10.32497/jrm.v15i1.1782.
Downloads
Published
Issue
Section
License
Copyright (c) 2022 Fahriansyah Fahriansyah
This work is licensed under a Creative Commons Attribution-NonCommercial 4.0 International License.
This work is licensed under a Creative Commons Attribution-NonCommercial 4.0 International License.
